Use "auxiliary air intake" in a sentence
1. The auxiliary path compression chamber (P3) is provided with a second air intake port (B).
2. Amount of intake air CO2 per mole of intake air
3. Furnace air intake?
4. air-intake pipes
5. Air intake plenum for air induction channel
6. Intake air temperature (K)
7. Method for control of air intake and valve for air intake and its application
8. Amount of water in the intake air, based on a humidity measurement of intake air
9. Absolute throttle position/intake air throttle position (position of valve used to regulate intake air)
10. absolute throttle position / intake air throttle position (position of valve used to regulate intake air)
11. Absolute throttle position / intake air throttle position (position of valve used to regulate intake air)
12. Hydropneumatic anti-hammer tank with an air intake and control device, and air intake method
13. An intake tube extends from the housing for receiving intake air.
14. Intake system with air filter
15. - air vents and intake valves,
16. clean air (ambient air, intake air, charge air, inlet manifold) temperature sensors;
17. Check air-intake level, 8 seconds.
18. Intake manifold air leak: A lean condition due to an intake manifold air leak can cause Backfiring.
19. Air intake valve (7), if fitted
20. Air intake valve (3), if fitted
21. Relative humidity of the intake air
22. Absolute humidity of the intake air
23. Combination valves for controlling intake air
24. Engine air intake shut off valve
25. Absolute temperature of the intake air
26. relative humidity of the intake air ( %)
27. Absolute humidity of the intake air.
28. For the intake air (if different from the dilution air):
29. (ii) clean air (ambient air, intake air, charge air, inlet manifold) temperature sensors;
30. Perhaps if you were to channel the second auxiliary tank through the primary intake valve.
31. Idle air intake control device of engine
32. humidity of the intake air water per kg dry air
33. Air intake systems, including air cleaners and filters for cleaning air for engines
34. Ra= relative humidity of the intake air, %
35. Shut valve to auxiliary engines and emergency air.
36. — Air intake valve if fitted equipment (5)
37. humidity of the intake air, g water per kg dry air
38. 19 The paper developes a set of intake manifold auxiliary air and fuel ultrasonic atomization system, which was tested in the 492Q gasoline engine on an engine dynamometer.
39. humidity of the intake air, gram of water per kg dry air
40. Engine intake system with accessible, interchangeable air filters
41. humidity of the intake air in g water per kg dry air
42. absolute humidity of the intake air, g water per kg dry air
43. Dry intake air density = 1.293 kg/m3 with
44. Intake air mass flow rate on dry basis
45. Air intake filters being parts for ventilating, air-conditioning or refrigerating apparatus
46. Air intake hood for turbine inlet filter house
47. instantaneous intake air mass flow rate [kg/s]
48. The charged spray enters through the air intake valves at the beginning of the intake stroke.
49. Ha: absolute humidity of the intake air, g water per kg dry air
50. Ha = humidity of the intake air in g water per kg dry air
51. Dry to wet correction factor for the intake air
52. Vent door: movable panels used to regulate air intake.
53. Intake and exhaust valves for cylinder type air compressor
54. Passive vacuum cleaner nozzle with an air intake aperture
55. Individual remanufacturing for Air Mass Meters, Fuel Distributors, Warm Up Regulators and Auxiliary Air Device.
56. Intake and exhaust valves for a cylinder type air compressor.
57. R a= relative humidity of the intake air (per cent)
58. The relief valve (68) adjusts the air pressure of the air intake chamber (64).
59. Air distributor for an internal combustion engine and air intake system having an air distributor of this type
60. intake air mass flow rate on wet basis, kg/s
61. Air drawn into the intake is compressed by the compressor.
62. Mra = molecular mass of dry intake air (= 28.9 g/mol)
63. The intake and exhaust air lines are equipped with filters.
64. An air intake hood for channeling an incoming air flow downward in a filter house.
65. • including control of auxiliary equipment, e.g. air-conditioning compressors or oil pumps
66. with Ha absolute humidity of the intake air, g of water per kg of dry air.
67. > 20 degr difference between measured and modelled intake air temperature
68. Air intake hose for air supply to the combustion part of the engine comprising at least:
69. Smoke released near outdoor air intakes will indicate whether air is being drawn into the intake.
70. Provided is a tuyere assembly for a molten iron manufacturing apparatus, which is capable of preventing tuyere damage and reducing the combustion focal distance for higher combustion efficiency of an auxiliary fuel, and minimizing the abrasion of an intake pipe caused by the intake of the auxiliary fuel.
71. The air supplementation pipe is provided with a third air intake port (C) and a first outlet.
72. Conduits for heating, cooling and air intake circuits and water for vehicles
73. The blower (0017) is disposed inside the air-flow intake hood channel.
74. Air is introduced into the combustion chamber via intake valves (17, 18).
75. High rise building with a stair well and a intake air shaft
76. is the molar mass of the dry intake air = 28.965 g/mol
77. Carbon dioxide levels at the air intake should be close to outdoor levels, otherwise exhaust is being brought into the intake.
78. with Ha absolute humidity of the intake air as g of water per kg of dry air
79. Oil filters, petrol filters and intake air filters for internal combustion engines
80. A rangehood or air-conditioning rangehood comprising a blower (0017) and an air-flow intake hood channel.