Use "abrasion test" in a sentence
1. Abrasion test
2. ABRASION TEST
3. Abrasion and microslip test
4. Test of resistance to abrasion
5. TEST OF RESISTANCE TO ABRASION
6. No abrasion test/symbol is required
7. No abrasion test/symbol is required.
8. 6.1. Test of resistance to abrasion
9. Test for strength of straps after abrasion
10. For sun roofs, no abrasion test is required
11. Abrasion resistance of protective clothing material — Test methods
12. “ # or sun roofs, no abrasion test is required.”
13. 1.3.1. Test for strength of straps after abrasion
14. In the DIN 58196 abrasion test the protected surface does not show any damages after 50 test cycles with 100 abrasion strokes.
15. Adhesion test using cellophane tape and abrasion test using Tabore Abrasion Tester in the quality control of curtain wall glass are also discussed.
16. Test of resistance to abrasion on the inner face
17. 6.1.3.4. For sun roofs no abrasion test is required.
18. Test of resistance to abrasion on the outer face.
19. Test of resistance to abrasion on the outer face
20. 5.1.2. Test of resistance to abrasion on the inner face.
21. The luminous transmittance shall be measured before the abrasion test
22. 5.1.2 Test of resistance to abrasion on the inner face
23. GRSG agreed on the need to review the abrasion test.
24. The spectral transmittance shall be measured before the abrasion test
25. 5.1.4 Abrasion A sponsor may choose to develop a specific test to address only wear/abrasion and particulate generation.
26. No abrasion test/symbol is required for plastic glazings intended for
27. abrasion test in accordance with the requirements of Annex # K, item
28. The abrasion test in accordance with the requirements of Annex 14, paragraph 6.1.
29. Test of resistance to abrasion in accordance with the requirements of annex #, paragraph
30. Test of resistance to abrasion in accordance with the requirements of Annex # paragraph
31. abrasion test in accordance with the requirements of Annex II K, item 2.1;
32. For example, we test the rolling resistance under load, abrasion resistance and shock strength.
33. TWO BELT ASSEMBLIES ARE REQUIRED FOR THE ABRASION PROCEDURE AND THE MICRO-SLIP TEST
34. 4 The abrasiveness of hot deformed low chromium semi-steel was studied through the impact abrasion test. the characters of abrasion surface was analyzed.
35. Immediately before and after the abrasion, clean the test pieces in the following manner
36. Two belt assemblies are required for the abrasion procedure and the micro-slip test.
37. Taber Abrasion test is a method to simulate the Abrasion of materials in the laboratory, which is widely used in all kinds of materials, including plastics, coatings, laminates, leather, paper, textiles, floors and so on.In this paper, the test method ASTM D4060 is used to explain how to conduct the Taber Abrasion test in four ways.
38. Test of resistance to abrasion in accordance with the requirements of Annex 9, paragraph 2.
39. Test of resistance to abrasion in accordance with the requirements of point #.# of Annex # I
40. Only rigid plastic glazing with an abrasion resistant coating shall be submitted to this test
41. Test of resistance to abrasion in accordance with the requirements of Annex 17, paragraph 6.1
42. Only rigid plastic glazing with an abrasion resistant coating shall be submitted to this test.
43. Test of resistance to abrasion in accordance with the requirements of annex 9, paragraph 2.1.
44. Abrasion may be classified as flat Abrasion, edge Abrasion or flex Abrasion
45. 2.12.3. Test of resistance to abrasion in accordance with the requirements of Annex 18, paragraph 6.1.
46. Abraded particles shall be sucked away during the test so that they do not influence abrasion.
47. In a similar experiment, a greater variety of clast sizes has been used to test bone abrasion.
48. Test of resistance to abrasion in accordance with the requirements of section 2.1 of Annex III I.
49. 5 The abrasiveness of hot deformed low chromium semi - steel was studied through the impact abrasion test.
50. The relative attenuation quotient shall be measured by the method given in paragraph # before the abrasion test
51. Test of resistance to abrasion in accordance with the requirements of point 2.1 of Annex III I.
52. 2.4.4.1. Test of resistance to abrasion in accordance with the requirements of point 2.1 of Annex III I.
53. The expert from Hungary presented GRSG-108-15 proposing to clarify the requirements on the abrasion test machine.
54. The relative attenuation quotient shall be measured by the method given in paragraph 7.8.3.2.1.1., before the abrasion test.
55. Four laboratory crushers and three apparati to measure resistance to wear by abrasion from a studded tyres test (AN test) from three laboratories were compared and studied.
56. Abrasion-loss measuring device, abrasion-loss measuring method, abrasion-loss measuring program, and recording medium
57. The text reproduced below was prepared by the expert from Hungary to clarify the requirements on the abrasion test machine.
58. Bones may not be the lowest-priced wheel, but our abrasion test chart shows why Bones is the best value
59. The profiles of the rock fragments experienced changes during the test as a result of saturation and abrasion-induced stresses.
60. Abrasion device
61. The purpose of this test is to determine whether the resistance of a safety glazing to abrasion exceeds a specified value.
62. Abrasion tester
63. The purpose of this test is to determine whether the resistance of a safety-glass pane to abrasion exceeds a specified value
64. The suitability of the sand-blast test to assess resistance of hard rocks against abrasion is investigated for eight different rock types.
65. The purpose of this test is to determine whether the resistance of a safety-glass pane to abrasion exceeds a specified value.
66. Abrasion-resistant materials
67. Cutting, polishing (abrasion)
68. Burnishing by abrasion
69. High abrasion factor.
70. Abrasion-resistant belt
71. Outsoles abrasion resistance:
72. Resistance to abrasion
73. Abrasion resistant fabric
74. Abrasion detection device, wind power generator equipped therewith, and abrasion detection method
75. EN #- Outsoles- Abrasion resistance
76. Abrasion resistant conveyor belt
77. Abrasion-resistant catalyst carrier
78. Abrasion-resistant composite sheet
79. Abrasion-resistant decor sheet
80. Abrasion instruments (machine tools)