shear stress analysis in Vietnamese

@Chuyên ngành kỹ thuật
@Lĩnh vực: xây dựng
-sự tính (toán) trượt

Sentence patterns related to "shear stress analysis"

1. Stress, strain, bending, compression, shear, torsion, tension, hoop stress, fatigue;

2. 30 Relationship between MRF' s yield stress and magnetic flux density, the shear stress and magnetic flux density and shears tress and shear rate were investigated.

3. Key words: Ground improvement, undrained shear strength, consolidation, stress path, settlement.

4. Normal stress effects and time dependent shear thickening have also been observed.

5. Alternatively, they may form in a regional stress field with high differential stress through the propagation of shear fractures.

6. Analysis of Birches - Rhythm, Stress and Scansion

7. Key words: landslide, till, correlation, stratigraphy, back analysis, shear strength, residual, aerial photographs.

8. The effects of transverse shear and rotatory inertia are included in the analysis.

9. Using the shear resistance – shear displacement data from undrained monotonic ring shear tests and several processed horizontal earthquake accelerograms, the minimum peak earthquake acceleration necessary to cause a catastrophic shear failure under various seismic waveforms was estimated for conditions of no shear stress reversals on the sliding surface.

10. A specific case of the generalCarreau rate-dependent integral viscoelastic model (1), the MBC-model (9), is evaluated with steady simple shear data, small amplitude oscillatory shear data, stress growth data, and stress relaxation data for four polymer solutions.

11. The lateral flexion, rotation stress test, and lateral shear test are three specific manual Alar ligament tests.

12. The amplitude of this normal stress is proportional to that of the oscillatory shear and the components in phase and 90‡ out of phase with the oscillatory shear prove to be odd functions of the steady shear rate.

13. 14 The results show that the distributing of the maximum principal stress and maximum shear stress are mainly under the control of the landform and fault.

14. Primary sludge is found to be antithixotropic at low shear stress. Digested sludge does not exhibit time dependency.

15. The primary objective of the paper is to extend an algebraic Reynolds-stress model including a new expression for the turbulent shear stress, in order to describe the negative production of turbulent kinetic energy appearing in curved channel flows in a region between the points of maximum velocity and vanishing shear stress.

16. /I¿2?) - 4.63, and a critical shear stress at onset of gross melt fracture greater than 4 x 10?

17. 25 Conventional shellac records were very brittle; only a few ounces of shear stress would crack them in half.

18. The adhesive forces between leukocytes and the vascular endothelium are antagonized by the shear stress of the flowing blood.

19. Key words: beam-column connection, database, earthquake-resistant design, finite element analysis, reinforced concrete, shear strength, stirrups.

20. To Characterize the shear softening deformation of the grain contact: (5) τ = u s k si 1 + u s k si / τ S τ < c + σ n tanφ σ n tanφ when slipping where τ, u s, τ S, k si, c, and φ denote the shear stress, shear displacement, parameter controlling nonlinear shear deformation, initial shear stiffness, cohesion, and friction angle of the

21. Key words: analysis, concrete (prestress), flexure, partial prestressing, prestressing, strain, stress, steel.

22. It is important to stress the need for a robust analysis of alternatives.

23. Cyclic motion, and its associated shear stress, appear to favor the formation of a cartilage callus, and thus healing through endochondral ossification.

24. The classical Westergaard type stress function analysis for in-plane stress crack problems is adapted to classical bending of cracked plates for determination of mode-1 stress intensity factors.

25. Allowable shearing stresses for shear walls should be taken as the sum of the Allowable shear stress given in Table 11.5 or 11.6 and one-fifth the average compressive stress produced by dead load at the level being analyzed, but not more than the maximum values listed in these tables.