nominal diameter of the hole in Vietnamese

@Chuyên ngành kỹ thuật
@Lĩnh vực: xây dựng
-đường kính danh định của lỗ khoa

Sentence patterns related to "nominal diameter of the hole"

Below are sample sentences containing the word "nominal diameter of the hole" from the English - Vietnamese Dictionary. We can refer to these sentence patterns for sentences in case of finding sample sentences with the word "nominal diameter of the hole", or refer to the context using the word "nominal diameter of the hole" in the English - Vietnamese Dictionary.

1. achromatic lens # mm nominal focal length and # mm nominal diameter

2. achromatic lens, 1,000 mm nominal focal length and 75 mm nominal diameter

3. The pilot diameter should match the diameter of the hole the Counterbore will be used in.

4. Our program is set to cut at the nominal part diameter

Chương trình của chúng tôi được thiết lập để cắt đường kính danh nghĩa phần

5. For cutter hole diameter is the diameter of the cutter that the Arbor is compatible with

6. Should always be cut to match the nominal work piece diameter

Nên luôn luôn được cắt giảm để phù hợp với đường kính mảnh làm việc trên danh nghĩa

7. The screw penetration hole has a diameter which is larger than the maximum diameter of the thread of the screw and the center hole formed in the washer.

8. This hole was a scant .23 inches in diameter.

9. This is the diameter of the Counterbore's pilot, which should match the diameter of the hole the Counterbore will be used in

10. Silver open scroll pattern with Black Antiquing large hole beads, 8mm x 8mm, hole diameter 6mm, package of 100 EleganciaBeads

11. This graphic illustrates what would happen if you did not cut to the nominal part diameter

Hình ảnh này minh hoạ những gì sẽ xảy ra nếu bạn đã không cắt với đường kính danh nghĩa phần

12. And our program set to cut to the nominal part diameter, these jaws are ready to cut

Và chúng tôi chương trình thiết lập để cắt với đường kính danh một phần, các hàm sẵn sàng để cắt

13. Note: For valves with different inlet and outlet diameters, the "nominal size" above refers to the smallest diameter. `

14. If the pilot diameter is larger than the hole, then the Counterbore won't fit

15. 2pcs 12mm Hole Diameter 45# Steel Tapered Bevel Gear 1.5 Module 16 Teeth

16. Schedule 80 Bulkheads do need a slightly larger diameter hole than ABS Bulkheads

17. Broaching process is used to clean any pre-existing hole or increase its diameter

18. THREAD DATA CHART: Metric Thread -- Coarse Pitch: Nominal Size ISO M: Thread Form Type: Major Diameter mm d=D: Pitch mm p: Root Radius mm r: Pitch Diameter mm d2=D2: Minor Diameter Male Thd

19. Also, the paper analyses the error caused by capillary action of liquid, error precision, zenith angle of hole and container diameter.

20. At Bittele Electronics the hole size for Castellated holes must be at least 0.5mm in diameter with space between hole edges to be at least 0.4mm.

21. The sizes of Countersinks in each set depend on the diameter of the hole; in all sets, the vertex angle is 60°.

22. Iron or steel nuts turned from bars, rods, profiles, or wire, of solid section, of a hole diameter ≤ 6 mm

23. Roughneck Auger type Post Hole Digger for digging and scooping out a hole of 125mm (5in) diameter, has a hardened blade that will cut through most soils and clays

24. Nominal voltage of the alternator

25. The Barcor Chamfer Gage is a precision instrument designed specifically to measure the top (major) diameter of a Chamfer, countersink or tapered hole