angularity in Vietnamese

Danh từ
1. sự có góc, sự thành góc
2. sự gầy còm, sự giơ xương; vẻ xương xương (người, mặt)
3. tính không mềm mỏng, tính cộc lốc; tính cứng đờ (dáng...)

Sentence patterns related to "angularity"

1. “Angularity.” Merriam-Webster.com Dictionary, Merriam-Webster, https://www.merriam-webster.com/dictionary/Angularity

2. What are synonyms for Angularity?

3. Gaging and Measurement of Angularity

4. Synonyms for Angularity in Free Thesaurus

5. 1 synonym for Angularity: angular shape

6. Angularity Checks – Parallel Flanges or Yokes

7. What does Angularity mean? Information and translations of Angularity in the most comprehensive dictionary definitions resource on the web.

8. Definition of Angularity in the Definitions.net dictionary

9. Angularity Sentence Examples A*C*G maps are tools to describe the effect of planetary Angularity upon the earth for a given moment of time. Angularity data show that Byzantine samples (Table 10; …

10. Angularity - WordReference English dictionary, questions, discussion and forums

11. Structure is the Angularity of the fine aggregate

12. Familiarity information: Angularity used as a noun is rare.

13. In the first sketch, the two couplings have no Angularity.

14. Angularity and flat panes are typical of this architectural style.

15. Angularity for a circular hole applies to the hole’s axis

16. The angularity requirement in point 4.2.5.3.1.1. may not be met in some cases.

17. Acterization, shape, and Angularity or index tests that use some engineering properties, such as po-rosity, to speculate on the shape, Angularity, and surface texture of aggregates

18. Also Angularity tolerance zone can be defined as a three-dimensional

19. Angularity (plural angularities) (uncountable) The property or characteristic of possessing angles

20. Angularity definition: the condition of being angular Meaning, pronunciation, translations and examples

21. There should not be any political angularity to be looked at it.

22. Angularity: Angularity tolerance symbol is shown as "∠".Angularity tolerance specifies a tolerance zone defined by two parallel plane at the specified angle other than 90 degree from a datum plane or axis within where the surface or the axis of the feature must lie

23. Angularity is an orientation control and uses a tolerance zone similar to parallelism and perpendicularity

24. 56 minutes ago · Refer to the Angularity geometric tolerance

25. Angularity translate: sự có góc; sự gầy còm

26. Angularity Number Angularity Number of an aggregate is the amount (to the higher whole number) by which the percentage of voids in it after compacting in a prescribed manner exceeds 33

27. The Angularity symbol is often used to insure that the part can properly mate with another

28. The Angularity is oiten referred to as the particle shape and surface texture

29. Parallelism, perpendicularity, and Angularity, in an easy-to-understand manner, using sample drawing indications

30. Angularity describes the specific orientation of one feature to another at a referenced angle

31. If your engineering drawing specifies an Angularity - that is what you should measure for.

32. QUANTIFY SHAPE, Angularity AND SURFACE TEXTURE OF AGGREGATES USING IMAGE ANALYSIS AND STUDY THEIR EFFECT ON PERFORMANCE 6

33. Other methods such as dedicated air gages or CMM can be used to verify Angularity

34. 1 day ago · Time dissipates to shining ether the solid Angularity of facts

35. ‘This face looks best in finer frames that don't draw attention to any heaviness or Angularity.’.

36. The Angularity is the difference between the maximum and minimum values of the dial gauge run-out.

37. But Angularity can be just as simple to understand, and measure, if a few things are known

38. Angularity is the symbol that describes the specific orientation of one feature to another at a referenced angle

39. Basically stated, Angularity is the gap difference across two coupling faces-normally top to bottom, or side to side

40. Rounding, roundness or Angularity are terms used to describe the shape of the corners on a particle (or clast) of sediment

41. An Angularity (applied to a surface) control requires a variable gage to find the high and low points of the surface

42. Angularity applied on non feature of size creates tolerance zone consists of two parallel planes and all the surface elements must lies within tolerance zone. When Angularity is applied on cylindrical feature of size, tolerance zone is a cylinder, diameter of tolerance value referenced in feature control frame

43. This short clip shows a method of checking Angularity using a dial test indicator and a sine bar on a surface plate

44. / ˌæŋ.ɡjəˈler.ə.t̬i / the quality of having angles rather than curves: The Angularity of the rocks indicates chemical weathering by the atmosphere

45. Angularity is typically measured by sweeping an indicator, probe, or other sensor over the surface to ensure all points lie within the parallel planes.

46. Curve: [verb] to have or take a turn, change, or deviation from a straight line or plane surface without sharp breaks or angularity.

47. This causes the Angularity of the eccentric rods to work in opposition to that of the connecting rod, and serves to equalize the power in the cylinder

48. As nouns the difference between angle and Angularity is that angle is (senseid)(geometry) a figure formed by two rays which start from a common point (a plane angle) or by three planes that intersect (a solid angle) or angle can be a fishhook; tackle for catching fish, consisting of a line, hook, and bait, with or without a rod while Angularity is

49. ‘At times, the dancers appear to be flying or diving; at others, they move with the spasmodic Angularity attributed to robots, their faces expressionless masks.’

50. Coarse aggregate Angularity is determined by computing the percentage of coarse aggregate particles with fractured faces. A sample of coarse aggregate is divided into three groups.