contact angle in Hungarian
felfekvésihajlásszög
Sentence patterns related to "contact angle"
1. The advancing contact angle and the receding contact angle were used.
2. The maximum possible contact angle is referred to as the advancing contact angle.
3. The receding contact angle is obtained as part of the solution.
4. Contact angle measurement followed to determine hydrophobizing of such treated wood.
5. If the network distance, squeegee and plates between squeegee contact angle is small.
6. As a result the contact angle of an applied water droplet increased significantly.
7. Appliance for determining the contact angle of a drop applied to a base
8. The results of contact angle measurements revealed that surface densification process affects surface wettability.
9. These include wall slip, liquid velocity, surface tension and the contact angle of liquids.
10. Contact angle is the scientific method of measuring the water repellency of a surface.
11. Thermal modification in soybean oil increased the wettability of the surface to water (reduced contact angle).
12. Device and method for determining the contact angle of a liquid body with a solid surface
13. The release potential, mechanical properties, surface tension, and contact angle of the cross-linked polymer were measured.
14. Density, shrinkage, pH, contact angle and water absorption of the treated and untreated wood blocks were determined.
15. The surface wettability, (contact angle), amount of oil uptake, water absorption and thickness swelling were determined thereafter.
16. We also offer special high-speed Bearings with phenolic resin cages and a 15° contact angle.
17. Heat treatment and oil treatment of the surface densified wood additionally increased the contact angle of tested liquids.
18. KRÜSS supports a full line of tensiometers and contact angle measuring instruments and provide you with expert guidance.
19. The effects of the surface tension and the contact angle on the collapsing bubble were taken into account.
20. The contact angle of the body is ascertained from the roll duration, the rolling path, and the roll angle.
21. Measuring contact angle, wetting, surface tension, interfacial tension, surface energy and surface viscosity for stability of emulsions and foams.
22. SKF 7308 Begam Angular Contact Bearing - 40 mm Bore, 90 mm OD, 23 mm Width, Open, 40 ° Contact Angle
23. The hydrophilic surface has a contact angle with water of Theta, Theta being equal to or less than (90°-Alpha/2).
24. The Bearings in this series are assembled with a specific internal clearance, so that they will have a specified contact angle under load
25. The method is suitable for particles of various shapes. Some examples of wet contact angle determinations for graphite, talc, coal, etc. are given.
26. Buy SKF 7312 Begam Angular Contact Bearing - 60 mm Bore, 130 mm OD, 31 mm Width, Open, 40 ° Contact Angle at Motion Industries
27. 28 Simulate the water film formation conditions at the time of tillage parts touching soil, tested the optimal combination of etching Plowshare Steel surface contact angle.
28. A good correlation between the contact angle of water and the ice adhesion strength was shown and the fraction of ice adhesion caused by hydrogen bonding was determined.
29. The paper describes the adhesion of algal spores to glass surfaces with different degrees of roughness (surface tension, contact angle and adsorption capacity were taken as indices of roughness).
30. Unless splash occurs, the equilibrium contact angle greatly affects the surface roughness on the wetting dynamics, which in turn alter friction forces at the wall and, therefore, the energy dispersed during spread.
31. The effects of the velocity, humidity, and temperature of the air stream, the contact angle to water droplet, and the temperature of the cooled plate on the frost formation are extensively determined.
32. In addition, as the conductive polymer of the present invention contains a fluorine component, it has a high contact angle by itself, and thus has a number of advantages including contamination prevention and high electrical conductivity.
33. Disclosed is a method for manufacturing a TFT substrate that is provided with a thin film transistor having a CuMn alloy film, said method including a control step for controlling a contact resistance on a CuMn alloy film surface on the basis of a contact angle of the CuMn alloy film surface.